Pitch & Rafter

Roof pitch calculator

Find the pitch, angle and slope of a roof from any one measurement. Then enter your house size to get rafter length, roof area and how many bundles of shingles to order.

What do you know?

Pick the measurement you have. The other two are worked out for you.

in
How far the roof goes up.
in
How far it goes across, measured level.

Your roof

Diagram of the roof slope
Pitch
6/12
Angle
26.57°
Slope
50%
Multiplier
1.118

Roof area and shingles

For a gable or hip roof with the same pitch on every side. Measure the house at ground level, wall to wall.

ft
ft
in
How far the roof sticks out past the wall.
%
10 for a simple roof, 15 for hips and valleys.
Most shingles come 3 bundles to a square. Check the wrapper.
  • Roof area0
  • Squares to order0
  • Shingle bundles0
  • Rafter length0

What roof pitch means

Pitch is how steep a roof is. In the US it is written as inches of rise for every 12 inches of run, so a 6/12 roof climbs 6 inches for each foot it travels across. The run is always measured level, never along the roof itself.

Pitch = rise ÷ run × 12

The same steepness can be given as an angle or as a percent. All three describe one slope.

Angle = arctan(rise ÷ run)   and   Slope % = rise ÷ run × 100

How to measure your roof pitch

  1. Hold a level flat against the underside of a rafter in the attic, or on top of the shingles.
  2. Mark 12 inches along the level from the end that touches the roof.
  3. At that 12 inch mark, measure straight down (or up) to the roof. That number is the rise.

If you measured 6 inches, you have a 6/12 roof. Measuring from the attic is safer than climbing on the roof.

Common roof pitches

The multiplier turns flat area into roof area.
PitchAngleSlopeMultiplier
1/124.76°8.3%1.003
2/129.46°16.7%1.014
3/1214.04°25.0%1.031
4/1218.43°33.3%1.054
5/1222.62°41.7%1.083
6/1226.57°50.0%1.118
7/1230.26°58.3%1.158
8/1233.69°66.7%1.202
9/1236.87°75.0%1.250
10/1239.81°83.3%1.302
11/1242.51°91.7%1.357
12/1245.00°100.0%1.414

From pitch to roof area

A sloped roof covers more surface than the floor below it. The pitch multiplier tells you how much more.

Multiplier = √(1 + (pitch ÷ 12)²)

Roof area = (length + 2 × overhang) × (width + 2 × overhang) × multiplier

A worked example

A 40 by 30 foot house with a 12 inch overhang covers 42 by 32 feet, or 1,344 square feet. At 6/12 the multiplier is 1.118, so the roof is about 1,503 square feet. Add 10% for waste and you need 1,653 square feet of shingles. Roofing is sold by the square, which is 100 square feet, so that is 16.5 squares or 50 bundles.

Rafter length uses the same multiplier. Half the 30 foot width plus the 1 foot overhang is a 16 foot run, and 16 × 1.118 is 17 feet 10⅝ inches from the ridge to the edge of the eave.

Common questions

What is the most common roof pitch?

Most houses in the US fall between 4/12 and 9/12. Lower pitches are common on ranch houses and additions. Steeper ones show up where snow needs to slide off.

What is the lowest pitch for asphalt shingles?

Shingle makers and most building codes set the minimum at 2/12, and roofs between 2/12 and 4/12 usually need extra underlayment. Below 2/12 a roof needs a membrane or another low-slope material. Check your local code and the shingle maker's instructions before you buy.

Can I walk on my roof?

Roofers generally treat anything up to about 6/12 as walkable with care, and anything steeper as needing roof jacks or a harness. Wet, icy or mossy shingles are slippery at any pitch.

Does this work for a hip roof?

Yes, as long as every side has the same pitch. The area comes out the same as a gable roof over the same house. Hip roofs do waste more shingles on the angled cuts, so use 15% instead of 10%.